Man with spanners - thinks he's a mechanic
Moderator: Contaminated
- ChrisL
- Posts: 1799
- Joined: Wed Jun 15, 2011 9:42 pm
- Location: Bedfordshire
- Contact:
Re: Man with spanners - thinks he's a mechanic
Yea I got a discount, about half the cost of the first clutch kit. I'll eBay the kit and the helix friction plate so should come to about even
Yes I've been drinking, what of it!!
- ChrisL
- Posts: 1799
- Joined: Wed Jun 15, 2011 9:42 pm
- Location: Bedfordshire
- Contact:
Re: Man with spanners - thinks he's a mechanic
Damn, yesterday it turns out the pulley squeal stopped as a hose blew off, so it's back again. I don't think I can make the belt wrap the pulley much more. Just wondering if it is caused by using an aluminium pulley? Would I better off with a steel one? Any tips on getting the squealing to stop or any other reasons that could be causing it?
Yes I've been drinking, what of it!!
- SteveRST
- Posts: 1261
- Joined: Sat Aug 18, 2012 12:23 pm
- Location: Chessington
- Contact:
Re: Man with spanners - thinks he's a mechanic
Hi Chris, I take it that the squealing is just related to the supercharger pulley?
It does look like it's wrapped around enough of the pulley. Can you tension the belt further or do you feel it should be tight enough? Any contamination of belt or pulleys causing slip?
Good luck, you're getting there!
It does look like it's wrapped around enough of the pulley. Can you tension the belt further or do you feel it should be tight enough? Any contamination of belt or pulleys causing slip?
Good luck, you're getting there!
Westfield Zetec turbo & Westfield Megabusa turbo
- ChrisL
- Posts: 1799
- Joined: Wed Jun 15, 2011 9:42 pm
- Location: Bedfordshire
- Contact:
Re: Man with spanners - thinks he's a mechanic
So I’ve roughed up the belt and SC pulley and tightened the belt as much as I dare and it’s a bit better but still far from where it needs to be, below are links to 2 videos 1showing the SC noise at idle the other the squealing, I’m not sure if the “as new” SC is as good as it should be, also the body of the SC is getting up to 100 C
https://youtu.be/VXGugMx-wBo
https://youtu.be/KSBDgRjFV0Q
https://youtu.be/VXGugMx-wBo
https://youtu.be/KSBDgRjFV0Q
Yes I've been drinking, what of it!!
- Nash
- Posts: 9877
- Joined: Thu Mar 04, 2010 9:12 pm
- Location: near Ashford, Kent
- Contact:
Re: Man with spanners - thinks he's a mechanic
That sounds distinctly like a lobe is touching the bore! Pull the lobe and look for scoring.
Buckle Up - Adventure Calls
-
- Posts: 2217
- Joined: Mon Jun 27, 2011 12:16 pm
- Location: Gillingham
- Contact:
Re: Man with spanners - thinks he's a mechanic
Not sure why this is happening , I think i may have seen something in the video but need to be sure have sent you a pm
-
- Posts: 2217
- Joined: Mon Jun 27, 2011 12:16 pm
- Location: Gillingham
- Contact:
Re: Man with spanners - thinks he's a mechanic
The problem i think is one of 2 things or both the gearing of the supercharger is incorrect causing to much pressure resulting in requiring a high torque to turn the supercharger this causes belt slippage . It looks like from the video that you are creating boost pressure at low engine rpm the pipes seem to be expanding at very low rpm . Once again this gives the same effect as incorrect gearing. hard to describe what is what without an installation drawing of what you have done or seeing the car in the flesh . All ways willing to talk on the phone if i can help
- ChrisL
- Posts: 1799
- Joined: Wed Jun 15, 2011 9:42 pm
- Location: Bedfordshire
- Contact:
Re: Man with spanners - thinks he's a mechanic
I've been off air for a while, working on a possible fix, apologies.
The SC is running a 65mm pulley on a standard zebec BT crank. I'm copying a known good set up, so I'm happy I'm not trying to over run the charger.
In the video I've only got a single throttle body (TB) infront of the plenum. I've added a second in front of the SC and in doing so discovered that the vacuum hose for the blow off valve was missing!
Currently the car sounds like a tank but doesn't squeal quite as much. I'll update once I've had some time to try and fettle and many thanks for the offers of help, I'll be picking up the phone if I don't make any progress
The SC is running a 65mm pulley on a standard zebec BT crank. I'm copying a known good set up, so I'm happy I'm not trying to over run the charger.
In the video I've only got a single throttle body (TB) infront of the plenum. I've added a second in front of the SC and in doing so discovered that the vacuum hose for the blow off valve was missing!
Currently the car sounds like a tank but doesn't squeal quite as much. I'll update once I've had some time to try and fettle and many thanks for the offers of help, I'll be picking up the phone if I don't make any progress
Yes I've been drinking, what of it!!
- ChrisL
- Posts: 1799
- Joined: Wed Jun 15, 2011 9:42 pm
- Location: Bedfordshire
- Contact:
Re: Man with spanners - thinks he's a mechanic
Pic of what it looks like now:
The blow off opens between the outlet and inlet of the SC when the SC outlet create a vacuum (I think!)
The blow off opens between the outlet and inlet of the SC when the SC outlet create a vacuum (I think!)
Yes I've been drinking, what of it!!
-
- Posts: 2217
- Joined: Mon Jun 27, 2011 12:16 pm
- Location: Gillingham
- Contact:
Return to “Car Related Discussion”
Who is online
Users browsing this forum: No registered users and 36 guests