I know it’s Fathers Day but I’m free so is anyone out and about? I have 60ltrs of v-power to get through after the meteorological anathema at Brands this week.
Can always do a short one if people need to be back.
Location depending on attendance.
07:00 for 07:15?
Sunday 16th June
Moderator: Contaminated
- Weathers
- Posts: 1024
- Joined: Thu Nov 17, 2016 2:32 pm
- Contact:
- graham b
- Posts: 4480
- Joined: Tue Dec 21, 2010 7:49 am
- Location: worthing , west sussex
- Contact:
Re: Sunday 16th June
Possible.
Depending on
start /finishing point.
Depending on
start /finishing point.
graham b
Lotus elise
Supercharged.
BBR Mx5
caterham R300
Westfield seiw
Tiger e1
Lotus elise
Supercharged.
BBR Mx5
caterham R300
Westfield seiw
Tiger e1
-
- Posts: 2123
- Joined: Mon Mar 01, 2010 7:38 pm
- Contact:
Re: Sunday 16th June
I would love to but I,ve just sheared a bolt off while removing the inlet manifold to fix a leak. Its going to have to be drilled out and re threaded.
- Weathers
- Posts: 1024
- Joined: Thu Nov 17, 2016 2:32 pm
- Contact:
Re: Sunday 16th June
I’ve got a tap and die set if that’s any use?
I think I’ve got a specific sheared bolt removal tool. I’ll have a look see tomorrow.
There has got to be any easy way. Can you get easily to the bolt? Cut a groove in the top and use a flat head driver to remove it? I use that technique all the time for stuff after someone on here suggested it when I was having trouble with the bolts on my seats. It was a revelation!!!
I think I’ve got a specific sheared bolt removal tool. I’ll have a look see tomorrow.
There has got to be any easy way. Can you get easily to the bolt? Cut a groove in the top and use a flat head driver to remove it? I use that technique all the time for stuff after someone on here suggested it when I was having trouble with the bolts on my seats. It was a revelation!!!
-
- Posts: 2123
- Joined: Mon Mar 01, 2010 7:38 pm
- Contact:
Re: Sunday 16th June
Thanks Chris.
Absolutely no chance of it moving with a screwdriver. Its in the cylinder head and stainless steel so a right mare. To make it harder it goes at around 45 degrees to the face
Absolutely no chance of it moving with a screwdriver. Its in the cylinder head and stainless steel so a right mare. To make it harder it goes at around 45 degrees to the face
- Weathers
- Posts: 1024
- Joined: Thu Nov 17, 2016 2:32 pm
- Contact:
Re: Sunday 16th June
kenton wrote:Thanks Chris.
Absolutely no chance of it moving with a screwdriver. Its in the cylinder head and stainless steel so a right mare. To make it harder it goes at around 45 degrees to the face
Oh bugger. So what’s the plan? Head off and to a metal engineer? Are you going to replace all of the bolts so next time they don’t all do it? You could change the cams whilst the heads away. Give you something to do.
-
- Posts: 2123
- Joined: Mon Mar 01, 2010 7:38 pm
- Contact:
Re: Sunday 16th June
Weathers wrote:kenton wrote:Thanks Chris.
Absolutely no chance of it moving with a screwdriver. Its in the cylinder head and stainless steel so a right mare. To make it harder it goes at around 45 degrees to the face
Oh bugger. So what’s the plan? Head off and to a metal engineer? Are you going to replace all of the bolts so next time they don’t all do it? You could change the cams whilst the heads away. Give you something to do.
New bolt set ordered (3/8th unc). set of taps too. Going to have a go myself with some cobalt drills. How hard can it be? its not as if anything could go wrong!
-
- Posts: 2123
- Joined: Mon Mar 01, 2010 7:38 pm
- Contact:
- Weathers
- Posts: 1024
- Joined: Thu Nov 17, 2016 2:32 pm
- Contact:
Re: Sunday 16th June
Definitely slowly slowly slowly does it.
I have drilled out a few things in my time albeit not that important and patience, a decent drill and drill bits are all required in equal measure. Plus a couple of brave pills!
I have drilled out a few things in my time albeit not that important and patience, a decent drill and drill bits are all required in equal measure. Plus a couple of brave pills!
- Tony B
- Site Admin
- Posts: 6333
- Joined: Sat Feb 20, 2010 1:57 pm
- Location: Maresfield, East Sussex
- Contact:
Re: Sunday 16th June
kenton wrote:20190614_101309.jpg
youve got the drill in the wrong hole
Who is online
Users browsing this forum: No registered users and 14 guests