Page 2 of 3

Re: Hello to all

Posted: Tue May 28, 2019 6:59 am
by Fury1630
Well done! Sounds like you know what you're doing behind a spanner, so a X-flow shouldn't present too many problems if it's done a 100 mile run already.

There's a WOW (Way Out West) run starting from Blackbushe in July here:-
https://www.southernkitcars.com/forum/viewtopic.php?f=5&t=10575
Could be good for you?

Re: Hello to all

Posted: Tue May 28, 2019 8:24 am
by David T
Welcome Nick. Car looks a cracker.

Re: Hello to all

Posted: Wed May 29, 2019 5:24 am
by Crunchie Gears
Welcome Nick from a fellow Westerner. Your car looks very clean. Looking forward to seeing it dirty :D :D

Re: Hello to all

Posted: Sun Jun 02, 2019 8:06 am
by Nickdavies
Fury1630 wrote:Well done! Sounds like you know what you're doing behind a spanner, so a X-flow shouldn't present too many problems if it's done a 100 mile run already.

There's a WOW (Way Out West) run starting from Blackbushe in July here:-
https://www.southernkitcars.com/forum/viewtopic.php?f=5&t=10575
Could be good for you?


Thanks. The xflow and all it's set up is new to me. Never had the chance to tinker and learn on the old stuff so nows my chance :D Got a few issues to sort out but should them done by then would be nice to attend

Re: Hello to all

Posted: Sun Jun 02, 2019 8:07 am
by Nickdavies
David T wrote:Welcome Nick. Car looks a cracker.


Thanks David

Re: Hello to all

Posted: Sun Jun 02, 2019 8:10 am
by Nickdavies
Crunchie Gears wrote:Welcome Nick from a fellow Westerner. Your car looks very clean. Looking forward to seeing it dirty :D :D

Thanks. It certainly doesn't look like that now :D

Re: Hello to all

Posted: Sun Jun 02, 2019 9:01 am
by Crunchie Gears
Nickdavies wrote:
Crunchie Gears wrote:Welcome Nick from a fellow Westerner. Your car looks very clean. Looking forward to seeing it dirty :D :D

Thanks. It certainly doesn't look like that now :D


Haha! Sounds like you are making progress. Hope to meet soon. Regards Paul

Re: Hello to all

Posted: Mon Jun 03, 2019 6:51 pm
by scotty
welcome along to a great and helpful club.
and congrats on the choice of engine haha!! i have a locost with a xflow have a spare now as i made the daft decision of tuning a 2nd engine...dont do this! been a year since i drove the car and wayyyyy to much cash lol i could of been enjoying the sun in what was lots of fun in the 1st place.

Re: Hello to all

Posted: Tue Jun 04, 2019 6:14 pm
by Nickdavies
scotty wrote:welcome along to a great and helpful club.
and congrats on the choice of engine haha!! i have a locost with a xflow have a spare now as i made the daft decision of tuning a 2nd engine...dont do this! been a year since i drove the car and wayyyyy to much cash lol i could of been enjoying the sun in what was lots of fun in the 1st place.

Thanks. I've got a lot of time for the xflow nice and simple and basic to work on makes a change from all the modern stuff I do day to day Haha. Have got a few engines I'm looking at to replace it over winter when I re-wire the entire car that's going to be a fun job. Best of luck getting it finished while the suns still shining

Re: Hello to all

Posted: Mon Jun 10, 2019 6:04 pm
by Hammy
Wow, that looks to be a nicely built car and if you're in the trade as it sounds like you are then you should have miles of smiles ahead!